[1970-Jan-01 00:01:30.885209]: Loading settings from string...
[1970-Jan-01 00:01:31.210868]: Parsing toolhead settings for bronx...
[1970-Jan-01 00:01:31.257545]: Rebuilding toolhead structure
[1970-Jan-01 00:01:31.286712]: Building bronx location 0...
[1970-Jan-01 00:01:31.480673]: Initialization: heater settings
[1970-Jan-01 00:01:31.482579]: storing heater 0 to time out after 3 minutes at temp, 1 minutes with no rise of 10C, fan feedforward amount 15C
[1970-Jan-01 00:01:31.510821]: Settings: Parsing home subtree...
[1970-Jan-01 00:01:31.537690]: Init endstop for axis: 0, type: load_sense, polarity: false
[1970-Jan-01 00:01:31.539621]: Init endstop for axis: 1, type: load_sense, polarity: false
[1970-Jan-01 00:01:31.551787]: Init endstop for axis: 2, type: switch, polarity: true
[1970-Jan-01 00:01:31.590832]: Parsing root settings...
[1970-Jan-01 00:01:31.641075]: STEPPER CONVERSIONS: Axis 0 steps per mm: 88.5732
[1970-Jan-01 00:01:31.662138]: STEPPER CONVERSIONS: Axis 1 steps per mm: 88.5732
[1970-Jan-01 00:01:31.663985]: STEPPER CONVERSIONS: Axis 2 steps per mm: 400
[1970-Jan-01 00:01:31.665771]: STEPPER CONVERSIONS: Axis 3 steps per mm: 108.55
[1970-Jan-01 00:01:31.667774]: STEPPER CONVERSIONS: Axis 0 periods per second 71392.9 seconds per period 1.4007e-05 slowest tickrate axis 0 tickrate 1.4007e-05 radices 32 2 30 0
[1970-Jan-01 00:01:31.680234]: STEPPER CONVERSIONS: Axis 1 periods per second 71392.9 seconds per period 1.4007e-05 slowest tickrate axis 0 tickrate 1.4007e-05 radices 32 32 30 0
[1970-Jan-01 00:01:31.682501]: STEPPER CONVERSIONS: Axis 2 periods per second 71392.9 seconds per period 1.4007e-05 slowest tickrate axis 0 tickrate 1.4007e-05 radices 32 32 32 0
[1970-Jan-01 00:01:31.684661]: STEPPER CONVERSIONS: Axis 3 periods per second 17847.6 seconds per period 5.603e-05 slowest tickrate axis 3 tickrate 5.603e-05 radices 32 32 32 31
[1970-Jan-01 00:01:31.687156]: syncing set to true
[1970-Jan-01 00:01:31.740564]: Axis count unspecified, defaulting to 4
[1970-Jan-01 00:01:31.780376]: Loading capacitor model settings for extruder 0
[1970-Jan-01 00:01:31.783908]: Have 1 valid ToolheadManager pointers, 0 is 0x1df800
[1970-Jan-01 00:01:31.897704]: setting driver address to 22
[1970-Jan-01 00:01:35.200815]: Init step: 0
[1970-Jan-01 00:01:35.260846]: Reset Toolhead Program State
[1970-Jan-01 00:01:35.262692]: Toolhead programmer: Resetting
[1970-Jan-01 00:01:35.264377]: done
[1970-Jan-01 00:01:36.186950]: Init step: 1
[1970-Jan-01 00:01:36.205226]: done
[1970-Jan-01 00:01:36.689917]: Init step: 2
[1970-Jan-01 00:01:36.702072]: done
[1970-Jan-01 00:01:37.192242]: Init step: 3
[1970-Jan-01 00:01:37.333382]: done
[1970-Jan-01 00:01:37.693978]: Init step: 4
[1970-Jan-01 00:01:37.721221]: done
[1970-Jan-01 00:01:38.204047]: Init step: 5
[1970-Jan-01 00:01:38.220451]: done
[1970-Jan-01 00:01:38.706071]: Init step: 5
[1970-Jan-01 00:01:38.821084]: done
[1970-Jan-01 00:01:39.209905]: Init step: 5
[1970-Jan-01 00:01:39.291374]: done
[1970-Jan-01 00:01:39.711529]: Init step: 5
[1970-Jan-01 00:01:39.721679]: done
[1970-Jan-01 00:01:40.219518]: Init step: 5
[1970-Jan-01 00:01:40.231916]: done
[1970-Jan-01 00:01:40.733997]: Init step: 5
[1970-Jan-01 00:01:40.836048]: done
[1970-Jan-01 00:01:41.244093]: Init step: 5
[1970-Jan-01 00:01:41.247328]: Toolhead 0: Packet 0x0: Calculated CRC: 0x62f5481b  Packet CRC: 0x0
[1970-Jan-01 00:01:41.249230]: Toolhead 0 : Toolhead Response Fail with comm_error: 1  Retry # : 1
[1970-Jan-01 00:01:41.261258]: done
[1970-Jan-01 00:01:41.746216]: Init step: 5
[1970-Jan-01 00:01:41.747997]: done
[1970-Jan-01 00:01:42.248067]: Init step: 5
[1970-Jan-01 00:01:42.261338]: done
[1970-Jan-01 00:01:42.749979]: Init step: 5
[1970-Jan-01 00:01:42.863140]: done
[1970-Jan-01 00:01:43.262153]: Init step: 5
[1970-Jan-01 00:01:43.270946]: Got valid API version 6 for Toolhead 0
[1970-Jan-01 00:01:43.277780]: done
[1970-Jan-01 00:01:44.061447]: Init step: 5
[1970-Jan-01 00:01:44.063736]: done
[1970-Jan-01 00:01:44.554015]: Init step: 5
[1970-Jan-01 00:01:44.656145]: done
[1970-Jan-01 00:01:45.055641]: Init step: 5
[1970-Jan-01 00:01:45.068248]: Toolhead 0: Toolhead has Firmware version 1.7,736
[1970-Jan-01 00:01:45.070404]:  Toolhead 0 initialized
[1970-Jan-01 00:01:45.072256]: done
[1970-Jan-01 00:01:45.558326]: Init step: 6
[1970-Jan-01 00:01:45.570753]: done
[1970-Jan-01 00:01:46.071717]: Init step: 7
[1970-Jan-01 00:01:46.074421]: done
[1970-Jan-01 00:01:46.582720]: bronx lowest mem space: 0x376 bytes
[1970-Jan-01 00:01:46.584625]: Checking tool eeprom version
[1970-Jan-01 00:01:46.586264]: Commanding tool usage stat retrieve
[1970-Jan-01 00:01:46.587914]: New tool uid 0x14441 attached, updating info cache
[1970-Jan-01 00:01:46.603221]: Connected tool has eepromv4
[1970-Jan-01 00:01:46.611766]: Raw usage stats: retract 814366452ct, extrusion 235955319 steps, 1010114 seconds, refurbed 0 times
[1970-Jan-01 00:01:46.613538]: Steps/mm not configured, tool usage logging will be wrong!
[1970-Jan-01 00:01:46.640520]: PRU Event: PRU_INIT
[1970-Jan-01 00:02:34.783197]: GetCachedToolUsageStats called
[1970-Jan-01 00:02:42.794061]: bronx lowest mem space: 0x372 bytes
[1970-Jan-01 00:05:38.093514]: bronx lowest mem space: 0x36e bytes
[1970-Jan-01 20:49:37.259252]: TH0: 2 failures in last 65536 packets (0.00305176%)
[1970-Jan-04 22:59:29.933758]: bronx lowest mem space: 0x36a bytes
[1970-Jan-06 02:48:04.532082]: bronx lowest mem space: 0x362 bytes
[1970-Jan-07 22:26:00.228672]: bronx lowest mem space: 0x35e bytes
[1970-Jan-15 19:08:22.611843]: Toolhead 0 state error: 54
[1970-Jan-15 19:08:22.646517]: Tool UID becomes 0.
[1970-Jan-15 19:08:31.205098]: Checking tool eeprom version
[1970-Jan-15 19:08:31.206941]: Commanding tool usage stat retrieve
[1970-Jan-15 19:08:31.209707]: New tool uid 0x14441 attached, updating info cache
[1970-Jan-15 19:08:32.721208]: Toolhead 0 state error: 0
[1970-Jan-15 19:08:32.722975]: Connected tool has eepromv4
[1970-Jan-15 19:08:32.727496]: Raw usage stats: retract 814366452ct, extrusion 235955319 steps, 1010114 seconds, refurbed 0 times
[1970-Jan-15 19:08:32.731267]: Steps/mm not configured, tool usage logging will be wrong!
[1970-Jan-15 19:13:27.983838]: Heater manager Set Target Temperature to 180, index 0
[1970-Jan-15 19:13:27.985717]: Sent heater settings hold timeout 3min, rise timeout 1min, rise threshold 10C, sag threhsold 20C, overrun threshold 20C, fan preload 15C, preload tick delay 8900ticks, temperature freeze timeout 54464ms (may be discretized)
[1970-Jan-15 19:13:29.270893]: bronx lowest mem space: 0x352 bytes
[1970-Jan-15 19:14:07.966527]: Heater manager Set Target Temperature to 215, index 0
[1970-Jan-15 19:14:07.968352]: Sent heater settings hold timeout 3min, rise timeout 1min, rise threshold 10C, sag threhsold 20C, overrun threshold 20C, fan preload 15C, preload tick delay 8900ticks, temperature freeze timeout 54464ms (may be discretized)
[1970-Jan-15 19:14:09.238586]: wait for heaters at target, wait bitmask 0x1
[1970-Jan-15 19:14:18.883504]: Toolhead 0 state error: 54
[1970-Jan-15 19:14:18.885307]: Tool UID becomes 0.
[1970-Jan-15 19:14:19.272502]: Toolhead Abort
[1970-Jan-15 19:14:19.278600]: aborting pru with shutdown=true
[1970-Jan-15 19:14:19.315353]: Last sync period had (0,0,7576320) buffer fulls due to suspend moves
[1970-Jan-15 19:14:19.346809]: Libstepper All Axis Abort
[1970-Jan-15 19:19:04.468001]: Heater manager Set Target Temperature to 0, index 0
[1970-Jan-15 19:19:04.480880]: Sent heater settings hold timeout 3min, rise timeout 1min, rise threshold 10C, sag threhsold 20C, overrun threshold 20C, fan preload 15C, preload tick delay 8900ticks, temperature freeze timeout 54464ms (may be discretized)
[1970-Jan-15 19:19:04.504278]: Checking tool eeprom version
[1970-Jan-15 19:19:04.506108]: Commanding tool usage stat retrieve
[1970-Jan-15 19:19:04.507809]: New tool uid 0x14441 attached, updating info cache
[1970-Jan-15 19:19:04.760891]: Toolhead 0 state error: 0
[1970-Jan-15 19:19:04.768724]: Connected tool has eepromv4
[1970-Jan-15 19:19:04.782710]: Raw usage stats: retract 814366452ct, extrusion 235955319 steps, 1010114 seconds, refurbed 0 times
[1970-Jan-15 19:19:04.784536]: Steps/mm not configured, tool usage logging will be wrong!
[1970-Jan-15 19:19:06.482044]: Last sync period had (0,0,7578033) buffer fulls due to suspend moves
[1970-Jan-15 19:19:06.484888]: Syncing turned false
[1970-Jan-15 19:19:06.486707]: Toolhead Abort
[1970-Jan-15 19:19:06.488475]: aborting pru with shutdown=true
[1970-Jan-15 19:19:06.491608]: Last sync period had (0,0,7578033) buffer fulls due to suspend moves
[1970-Jan-15 19:19:06.500350]: Libstepper All Axis Abort
[1970-Jan-15 19:19:06.502220]: Heater manager Set Target Temperature to 0, index 0
[1970-Jan-15 19:19:06.503975]: Sent heater settings hold timeout 3min, rise timeout 1min, rise threshold 10C, sag threhsold 20C, overrun threshold 20C, fan preload 15C, preload tick delay 8900ticks, temperature freeze timeout 54464ms (may be discretized)
[1970-Jan-15 19:19:06.505895]: Commanding tool usage stat retrieve
[1970-Jan-15 19:19:06.536999]: Raw usage stats: retract 814366452ct, extrusion 235955319 steps, 1010114 seconds, refurbed 0 times
[1970-Jan-15 19:19:06.538811]: Steps/mm not configured, tool usage logging will be wrong!
[1970-Jan-15 19:19:06.559809]: Commanding tool usage stat retrieve
[1970-Jan-15 19:19:06.579968]: Raw usage stats: retract 814366452ct, extrusion 235955319 steps, 1010114 seconds, refurbed 0 times
[1970-Jan-15 19:19:06.582016]: Steps/mm not configured, tool usage logging will be wrong!
[1970-Jan-15 19:19:10.414200]: Heater manager Set Target Temperature to 215, index 0
[1970-Jan-15 19:19:10.416083]: Sent heater settings hold timeout 3min, rise timeout 1min, rise threshold 10C, sag threhsold 20C, overrun threshold 20C, fan preload 15C, preload tick delay 8900ticks, temperature freeze timeout 54464ms (may be discretized)
[1970-Jan-15 19:19:11.638552]: wait for heaters at target, wait bitmask 0x1
[1970-Jan-15 19:21:57.968149]: Toolhead 0 state error: 80
[1970-Jan-15 19:22:00.208647]: Toolhead Abort
[1970-Jan-15 19:22:00.220921]: aborting pru with shutdown=true
[1970-Jan-15 19:22:00.230854]: Last sync period had (0,0,7588059) buffer fulls due to suspend moves
[1970-Jan-15 19:22:00.232668]: Libstepper All Axis Abort
[1970-Jan-15 19:22:00.560999]: Toolhead 0 state error: 0
[1970-Jan-15 19:22:14.483741]: libstepper: false toolhead: true( ignored: false) acceleration_manager: true
[1970-Jan-15 19:22:15.669809]: Toolhead 0 state error: 80
[1970-Jan-15 19:22:17.562120]: Toolhead 0 state error: 0
[1970-Jan-15 19:22:19.899627]: libstepper: false toolhead: true( ignored: false) acceleration_manager: true
[1970-Jan-15 19:22:21.884474]: Raw HES proceeding
[1970-Jan-15 19:22:21.902281]: Got raw val 22325, saturated: true
[1970-Jan-15 19:22:21.928694]: Returning HES
[1970-Jan-15 19:22:21.930646]: Sending back val 22325, saturated true
[1970-Jan-15 19:22:21.973977]: Toolhead Abort
[1970-Jan-15 19:22:21.975762]: aborting pru with shutdown=true
[1970-Jan-15 19:22:21.978613]: Last sync period had (0,0,7589358) buffer fulls due to suspend moves
[1970-Jan-15 19:22:21.980630]: Libstepper All Axis Abort
[1970-Jan-15 19:22:48.287196]: Heater manager Set Target Temperature to 215, index 0
[1970-Jan-15 19:22:48.289024]: Sent heater settings hold timeout 3min, rise timeout 1min, rise threshold 10C, sag threhsold 20C, overrun threshold 20C, fan preload 15C, preload tick delay 8900ticks, temperature freeze timeout 54464ms (may be discretized)
[1970-Jan-15 19:22:49.498687]: wait for heaters at target, wait bitmask 0x1
[1970-Jan-15 19:22:58.884021]: libstepper: false toolhead: false( ignored: false) acceleration_manager: true
[1970-Jan-15 19:23:06.216739]: libstepper: false toolhead: false( ignored: false) acceleration_manager: true
[1970-Jan-15 19:23:11.967187]: libstepper: false toolhead: true( ignored: false) acceleration_manager: true
[1970-Jan-15 19:23:17.276636]: libstepper: false toolhead: true( ignored: false) acceleration_manager: true
[1970-Jan-15 19:23:22.619554]: libstepper: false toolhead: true( ignored: false) acceleration_manager: true
[1970-Jan-15 19:23:28.151302]: libstepper: false toolhead: true( ignored: false) acceleration_manager: true
[1970-Jan-15 19:23:33.292263]: libstepper: false toolhead: true( ignored: false) acceleration_manager: true
[1970-Jan-15 19:23:38.186298]: libstepper: false toolhead: true( ignored: false) acceleration_manager: true
[1970-Jan-15 19:23:42.536071]: Raw HES proceeding
[1970-Jan-15 19:23:42.551797]: Got raw val 22478, saturated: true
[1970-Jan-15 19:23:42.576439]: Returning HES
[1970-Jan-15 19:23:42.578140]: Sending back val 22478, saturated true
[1970-Jan-15 19:23:42.645492]: Toolhead Abort
[1970-Jan-15 19:23:42.647400]: aborting pru with shutdown=true
[1970-Jan-15 19:23:42.650579]: Last sync period had (0,0,7592361) buffer fulls due to suspend moves
[1970-Jan-15 19:23:42.652392]: Libstepper All Axis Abort
[1970-Jan-15 19:23:58.808563]: Heater manager Set Target Temperature to 215, index 0
[1970-Jan-15 19:23:58.820687]: Sent heater settings hold timeout 3min, rise timeout 1min, rise threshold 10C, sag threhsold 20C, overrun threshold 20C, fan preload 15C, preload tick delay 8900ticks, temperature freeze timeout 54464ms (may be discretized)
[1970-Jan-15 19:24:00.025780]: wait for heaters at target, wait bitmask 0x1
[1970-Jan-15 19:24:05.506276]: libstepper: false toolhead: false( ignored: false) acceleration_manager: true
[1970-Jan-15 19:24:11.228690]: libstepper: false toolhead: false( ignored: false) acceleration_manager: true
[1970-Jan-15 19:24:16.482155]: libstepper: false toolhead: false( ignored: false) acceleration_manager: true
[1970-Jan-15 19:24:18.473311]: Steps overrun! last 62959 and just got 8278
[1970-Jan-15 19:24:18.475055]: calculated 10854
[1970-Jan-15 19:24:21.618078]: libstepper: false toolhead: true( ignored: false) acceleration_manager: true
[1970-Jan-15 19:24:26.762498]: libstepper: false toolhead: true( ignored: false) acceleration_manager: true
[1970-Jan-15 19:24:33.778750]: Raw HES proceeding
[1970-Jan-15 19:24:33.805067]: Got raw val 21810, saturated: true
[1970-Jan-15 19:24:33.889388]: Returning HES
[1970-Jan-15 19:24:33.891351]: Sending back val 21810, saturated true
[1970-Jan-15 19:24:33.938681]: Toolhead Abort
[1970-Jan-15 19:24:33.950761]: aborting pru with shutdown=true
[1970-Jan-15 19:24:33.953923]: Last sync period had (0,0,7594308) buffer fulls due to suspend moves
[1970-Jan-15 19:24:33.955895]: Libstepper All Axis Abort
[1970-Jan-15 19:24:39.400706]: Heater manager Set Target Temperature to 0, index 0
[1970-Jan-15 19:24:39.402652]: Sent heater settings hold timeout 3min, rise timeout 1min, rise threshold 10C, sag threhsold 20C, overrun threshold 20C, fan preload 15C, preload tick delay 8900ticks, temperature freeze timeout 54464ms (may be discretized)
[1970-Jan-15 19:25:44.890328]: Last sync period had (0,0,7594932) buffer fulls due to suspend moves
[1970-Jan-15 19:25:44.893048]: Syncing turned false
[1970-Jan-15 19:25:44.894860]: Toolhead Abort
[1970-Jan-15 19:25:44.896672]: aborting pru with shutdown=true
[1970-Jan-15 19:25:44.899546]: Last sync period had (0,0,7594932) buffer fulls due to suspend moves
[1970-Jan-15 19:25:44.901588]: Libstepper All Axis Abort
[1970-Jan-15 19:25:44.903269]: Heater manager Set Target Temperature to 0, index 0
[1970-Jan-15 19:25:44.905014]: Sent heater settings hold timeout 3min, rise timeout 1min, rise threshold 10C, sag threhsold 20C, overrun threshold 20C, fan preload 15C, preload tick delay 8900ticks, temperature freeze timeout 54464ms (may be discretized)
[1970-Jan-15 19:25:45.020654]: Heater manager Set Target Temperature to 0, index 0
[1970-Jan-15 19:25:45.022498]: Sent heater settings hold timeout 3min, rise timeout 1min, rise threshold 10C, sag threhsold 20C, overrun threshold 20C, fan preload 15C, preload tick delay 8900ticks, temperature freeze timeout 54464ms (may be discretized)
[1970-Jan-15 19:25:45.125415]: Commanding stats update: Retract count: 814366452
[1970-Jan-15 19:25:45.127279]: Toolhead 0 marked as possibly blocking!
[1970-Jan-15 19:25:45.722910]: Toolhead 0 done blocking!
[1970-Jan-15 19:25:45.872573]: GetToolUsageStats called in machine  state 0
[1970-Jan-15 19:25:45.874379]: Commanding tool usage stat retrieve
[1970-Jan-15 19:25:45.876271]: GetToolUsageState: Proceeds to 1
[1970-Jan-15 19:25:45.877956]: GetToolUsagState: Error from retrieve: 0x10a
[1970-Jan-15 19:25:45.892086]: Raw usage stats: retract 1628732904ct, extrusion 236042159 steps, 1010247 seconds, refurbed 0 times
[1970-Jan-15 19:25:45.893924]: Steps/mm not configured, tool usage logging will be wrong!
[1970-Jan-15 19:25:45.981657]: GetToolUsageStats called in machine  state 1
[1970-Jan-15 19:25:45.983454]: VerifyToolUsageStatsRetrieved: Done
[1970-Jan-15 19:25:45.985129]: GetToolUsageState: Proceeds to 2
[1970-Jan-15 19:25:46.013911]: GetToolUsageStats called in machine  state 2
[1970-Jan-15 19:25:46.015729]: GetToolUsageState: Done, resets
[1970-Jan-15 19:26:13.283405]: Heater manager Set Target Temperature to 180, index 0
[1970-Jan-15 19:26:13.285705]: Sent heater settings hold timeout 3min, rise timeout 1min, rise threshold 10C, sag threhsold 20C, overrun threshold 20C, fan preload 15C, preload tick delay 8900ticks, temperature freeze timeout 54464ms (may be discretized)
[1970-Jan-15 19:26:16.541645]: HOME: axis 1, speed 22, flip dir false, sp true, blocking false
[1970-Jan-15 19:26:16.643581]: Load Sense Limit Method: 1
[1970-Jan-15 19:26:16.651528]: Last sync period had (0,0,7595256) buffer fulls due to suspend moves
[1970-Jan-15 19:26:16.654125]: Libstepper All Axis Abort
[1970-Jan-15 19:26:17.467615]: libstepper: false toolhead: false( ignored: false) acceleration_manager: true
[1970-Jan-15 19:26:23.321025]: HOME: 1 homing: Limit Detected!: 
[1970-Jan-15 19:26:23.323006]: Toolhead Abort
[1970-Jan-15 19:26:23.324860]: aborting pru with shutdown=true
[1970-Jan-15 19:26:23.337861]: Last sync period had (0,0,7595544) buffer fulls due to suspend moves
[1970-Jan-15 19:26:23.339679]: Libstepper All Axis Abort
[1970-Jan-15 19:26:23.416835]: HOME: 1 homing: Limit Detected!: 
[1970-Jan-15 19:26:25.333782]: libstepper: true toolhead: true( ignored: false) acceleration_manager: true
[1970-Jan-15 19:26:25.368946]: HOME: axis 0, speed 22, flip dir false, sp true, blocking false
[1970-Jan-15 19:26:25.375379]: Load Sense Limit Method: 0
[1970-Jan-15 19:26:25.378278]: Last sync period had (0,0,7595631) buffer fulls due to suspend moves
[1970-Jan-15 19:26:25.380333]: Libstepper All Axis Abort
[1970-Jan-15 19:26:33.080428]: libstepper: false toolhead: true( ignored: false) acceleration_manager: true
[1970-Jan-15 19:26:39.511490]: HOME: 0 homing: Limit Detected!: 
[1970-Jan-15 19:26:39.513376]: Toolhead Abort
[1970-Jan-15 19:26:39.515271]: aborting pru with shutdown=true
[1970-Jan-15 19:26:39.518038]: Last sync period had (0,0,7596267) buffer fulls due to suspend moves
[1970-Jan-15 19:26:39.519915]: Libstepper All Axis Abort
[1970-Jan-15 19:26:39.605953]: HOME: 0 homing: Limit Detected!: 
[1970-Jan-15 19:26:41.277221]: libstepper: false toolhead: true( ignored: false) acceleration_manager: true
[1970-Jan-15 19:26:42.469505]: HOME: axis 2, speed 8, flip dir false, sp true, blocking false
[1970-Jan-15 19:26:47.993337]: libstepper: false toolhead: true( ignored: false) acceleration_manager: true
[1970-Jan-15 19:26:54.434278]: libstepper: false toolhead: true( ignored: false) acceleration_manager: true
[1970-Jan-15 19:27:01.123602]: libstepper: false toolhead: true( ignored: false) acceleration_manager: true
[1970-Jan-15 19:27:04.238133]: HOME: 2 homing: Limit Detected!: 
[1970-Jan-15 19:27:04.262165]: Toolhead Abort
[1970-Jan-15 19:27:04.263930]: aborting pru with shutdown=false
[1970-Jan-15 19:27:04.301735]: CLEAR BUFFER FAIL! in libstepper::Abort()
[1970-Jan-15 19:27:04.309100]: Last sync period had (0,0,7597473) buffer fulls due to suspend moves
[1970-Jan-15 19:27:04.311169]: Libstepper All Axis Abort
[1970-Jan-15 19:27:04.478375]: HOME: 2 homing: Limit Detected!: 
[1970-Jan-15 19:27:05.985828]: HOME: axis 2, speed 0.5, flip dir false, sp true, blocking true
[1970-Jan-15 19:27:06.263912]: HOME: 2 homing: Limit Detected!: 
[1970-Jan-15 19:27:06.271629]: Toolhead Abort
[1970-Jan-15 19:27:06.273399]: aborting pru with shutdown=false
[1970-Jan-15 19:27:06.286581]: Last sync period had (0,0,7597512) buffer fulls due to suspend moves
[1970-Jan-15 19:27:06.288401]: Libstepper All Axis Abort
[1970-Jan-15 19:27:06.357249]: HOME: 2 homing: Limit Detected!: 
[1970-Jan-15 19:27:06.588453]: GAP: Query->Await
[1970-Jan-15 19:27:06.618120]: TH0: Retreived step position 11796751
[1970-Jan-15 19:27:06.652280]: wait for PRU status in get position
[1970-Jan-15 19:27:06.653999]: wait for PRU status in get position
[1970-Jan-15 19:27:06.655631]: GAP: Await->Done(Query)
[1970-Jan-15 19:27:06.947144]: Heater manager Set Target Temperature to 180, index 0
[1970-Jan-15 19:27:06.948937]: Sent heater settings hold timeout 3min, rise timeout 1min, rise threshold 10C, sag threhsold 20C, overrun threshold 20C, fan preload 15C, preload tick delay 8900ticks, temperature freeze timeout 54464ms (may be discretized)
[1970-Jan-15 19:27:08.659980]: Expecting 138311 steps extruded this print from 1274.17 mm of plastic
[1970-Jan-15 19:27:09.030665]: Heater manager Set Target Temperature to 215, index 0
[1970-Jan-15 19:27:09.032493]: Sent heater settings hold timeout 3min, rise timeout 1min, rise threshold 10C, sag threhsold 20C, overrun threshold 20C, fan preload 15C, preload tick delay 8900ticks, temperature freeze timeout 54464ms (may be discretized)
[1970-Jan-15 19:27:09.286733]: wait for heaters at target, wait bitmask 0x1
[1970-Jan-15 19:28:21.014572]: libstepper: false toolhead: false( ignored: false) acceleration_manager: true
[1970-Jan-15 19:28:22.705941]: Expend Buffer: false
[1970-Jan-15 19:28:22.780334]: Syncing turned true
[1970-Jan-15 19:28:22.870172]: PRU Event: PRU_SYNC_ON(7)
[1970-Jan-15 19:28:22.871934]: PRU Event: PRU_SYNC_DELAY(6)
[1970-Jan-15 19:28:23.898820]: Toolhead 0  ADC Error: 1
[1970-Jan-15 19:28:24.163876]: PRU Event: PRU_SYNC_DELAY(5)
[1970-Jan-15 19:28:24.165631]: PRU Event: PRU_SYNC_DELAY(4)
[1970-Jan-15 19:28:24.167335]: PRU Event: PRU_SYNC_DELAY(3)
[1970-Jan-15 19:28:24.169026]: PRU Event: PRU_SYNC_DELAY(2)
[1970-Jan-15 19:28:24.182964]: PRU Event: PRU_SYNC_DELAY(1)
[1970-Jan-15 19:28:24.184685]: PRU Event: PRU_SYNC_DELAY(0)
[1970-Jan-15 19:29:04.578782]: Expected packet id: 0xbd, Got packet id: 0xbc, Full packet: 
0xf3,0x0,0x0,0x2d,0x0,0xd3,0x0,0xf,0x4f,0x99,0x1,0x0,0xd7,0x0,0x1,0x44,0x41,0x3,0x52,0x1,0x1,0x0,0x0,0x0,0x0,0xcb,0x0,0xbc,0x9c,0x7a,0x51,0x20,

[1970-Jan-15 19:29:04.581843]: Toolhead 0 : Toolhead Response Fail with comm_error: 117  Retry # : 1
[1970-Jan-15 19:29:19.748295]: Expected packet id: 0xa0, Got packet id: 0x9f, Full packet: 
0xf3,0x0,0x0,0x2d,0x0,0xd0,0x0,0xf,0x5c,0x4b,0x1,0x0,0xd7,0x0,0x1,0x44,0x41,0x3,0x52,0x1,0x1,0x0,0x0,0x0,0x1,0x5,0x0,0x9f,0x94,0xf5,0x2a,0x2c,

[1970-Jan-15 19:29:19.750770]: Toolhead 0 : Toolhead Response Fail with comm_error: 117  Retry # : 1
[1970-Jan-15 19:29:24.413695]: Expected packet id: 0xde, Got packet id: 0x1, Full packet: 
0x12,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0xf3,0x0,0x0,0x2d,0x0,0xd0,0x0,0xf,0x60,0x78,0x1,0x0,0xd7,0x0,0x1,0x44,0x41,0x3,0x52,

[1970-Jan-15 19:29:24.415646]: Toolhead 0 : Toolhead Response Fail with comm_error: 117  Retry # : 1
[1970-Jan-15 19:29:45.851971]: Expected packet id: 0xe5, Got packet id: 0x74, Full packet: 
0x12,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0xf3,0x0,0x0,0x2d,0x0,0xd1,0x0,0xf,0x74,0xbb,0x1,0x0,0xd7,

[1970-Jan-15 19:29:45.853929]: Toolhead 0 : Toolhead Response Fail with comm_error: 117  Retry # : 1
[1970-Jan-15 19:30:04.924087]: Toolhead 0 : Retry: Waited 0.640577s from state change
[1970-Jan-15 19:30:16.614861]: Expected packet id: 0xea, Got packet id: 0xf, Full packet: 
0x12,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0xf3,0x0,0x0,0x2d,0x0,0xd6,0x0,0xf,0x81,0x1a,0x1,0x0,

[1970-Jan-15 19:30:16.616984]: Toolhead 0 : Toolhead Response Fail with comm_error: 117  Retry # : 1
[1970-Jan-15 19:30:16.711535]: Expected packet id: 0xef, Got packet id: 0x0, Full packet: 
0x12,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0xf3,0x0,0x0,0x2d,0x0,0xd6,0x0,0xf,0x81,0x2d,0x1,0x0,0xd7,0x0,0x1,0x44,0x41,0x3,

[1970-Jan-15 19:30:16.713617]: Toolhead 0 : Toolhead Response Fail with comm_error: 117  Retry # : 1
[1970-Jan-15 19:30:19.947332]: Expected packet id: 0x9d, Got packet id: 0x9c, Full packet: 
0xf3,0x0,0x0,0x2d,0x0,0xd7,0x0,0xf,0x82,0xe1,0x1,0x0,0xd7,0x0,0x1,0x44,0x41,0x3,0x52,0x1,0x1,0x0,0x0,0x0,0x1,0x5,0x0,0x9c,0x1d,0xf2,0x56,0x70,

[1970-Jan-15 19:30:19.949283]: Toolhead 0 : Toolhead Response Fail with comm_error: 117  Retry # : 1
[1970-Jan-15 19:31:05.614201]: Toolhead 0 : Retry: Waited 0.61131s from state change
[1970-Jan-15 19:31:18.721942]: Expected packet id: 0x65, Got packet id: 0xd7, Full packet: 
0x12,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0xf3,0x0,0x0,0x2d,0x0,0xd4,0x0,0xf,0x94,0x66,0x1,0x0,0xd7,0x0,0x1,0x44,0x41,

[1970-Jan-15 19:31:18.723949]: Toolhead 0 : Toolhead Response Fail with comm_error: 117  Retry # : 1
[1970-Jan-15 19:31:26.363151]: Expected packet id: 0xb6, Got packet id: 0xd7, Full packet: 
0x12,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0xf3,0xf,0x0,0x2d,0x0,0xd6,0x0,0xf,0x96,0x59,0x1,0x0,0xd7,0x0,0x1,0x44,0x41,

[1970-Jan-15 19:31:26.365074]: Toolhead 0 : Toolhead Response Fail with comm_error: 117  Retry # : 1
[1970-Jan-15 19:31:34.823634]: Expected packet id: 0x28, Got packet id: 0x27, Full packet: 
0xf3,0x0,0x0,0x2d,0x0,0xd7,0x0,0xf,0x97,0xf3,0x1,0x0,0xd7,0x0,0x1,0x44,0x41,0x3,0x52,0x1,0x1,0x0,0x0,0x0,0x3,0x1a,0x0,0x27,0x50,0x88,0x56,0x73,

[1970-Jan-15 19:31:34.825565]: Toolhead 0 : Toolhead Response Fail with comm_error: 117  Retry # : 1
[1970-Jan-15 19:31:59.331595]: Expected packet id: 0x51, Got packet id: 0x1, Full packet: 
0x12,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0xf3,0x0,0x0,0x2d,0x0,0xd6,0x0,0xf,0x9d,0xf7,0x1,0x0,0xd7,0x0,0x1,0x44,0x41,0x3,0x52,

[1970-Jan-15 19:31:59.333547]: Toolhead 0 : Toolhead Response Fail with comm_error: 117  Retry # : 1
[1970-Jan-15 19:33:05.423884]: Toolhead 0 : Retry: Waited 0.626695s from state change
[1970-Jan-15 19:33:12.255452]: Expected packet id: 0xcb, Got packet id: 0x1, Full packet: 
0x12,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0xf3,0x0,0x0,0x2d,0x0,0xd6,0x0,0xf,0xaf,0xb0,0x1,0x0,0xd7,0x0,0x1,0x44,0x41,0x3,0x52,

[1970-Jan-15 19:33:12.257769]: Toolhead 0 : Toolhead Response Fail with comm_error: 117  Retry # : 1
[1970-Jan-15 19:34:06.603744]: Toolhead 0 : Retry: Waited 0.693331s from state change
[1970-Jan-15 19:34:35.107488]: Expected packet id: 0xf2, Got packet id: 0xf1, Full packet: 
0xf3,0x0,0x0,0x2d,0x0,0xd7,0x0,0xf,0xc4,0x3c,0x1,0x0,0xd7,0x0,0x1,0x44,0x41,0x3,0x52,0x1,0x1,0x0,0x0,0x0,0x0,0xc7,0x0,0xf1,0x46,0xcd,0xcc,0x50,

[1970-Jan-15 19:34:35.110537]: Toolhead 0 : Toolhead Response Fail with comm_error: 117  Retry # : 1
[1970-Jan-15 19:36:06.943630]: Toolhead 0 : Retry: Waited 0.664037s from state change
[1970-Jan-15 19:36:19.073509]: Expected packet id: 0x35, Got packet id: 0xd7, Full packet: 
0x12,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0xf3,0x0,0x0,0x2d,0x0,0xd6,0x0,0xf,0xe0,0x5e,0x1,0x0,0xd7,0x0,0x1,0x44,0x41,

[1970-Jan-15 19:36:19.075461]: Toolhead 0 : Toolhead Response Fail with comm_error: 117  Retry # : 1
[1970-Jan-15 19:36:28.825429]: Expected packet id: 0xa1, Got packet id: 0xd7, Full packet: 
0x12,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0xf3,0x0,0x0,0x2d,0x0,0xd6,0x0,0xf,0xe3,0x9,0x1,0x0,0xd7,0x0,0x1,0x44,0x41,

[1970-Jan-15 19:36:28.827370]: Toolhead 0 : Toolhead Response Fail with comm_error: 117  Retry # : 1
[1970-Jan-15 19:37:03.216447]: Expected packet id: 0xde, Got packet id: 0xdd, Full packet: 
0xf3,0x0,0x0,0x2d,0x0,0xd7,0x0,0xf,0xec,0x85,0x1,0x0,0xd7,0x0,0x1,0x44,0x41,0x3,0x52,0x1,0x1,0x0,0x0,0x0,0x0,0x86,0x0,0xdd,0xf3,0xfe,0xc9,0x6e,

[1970-Jan-15 19:37:03.218375]: Toolhead 0 : Toolhead Response Fail with comm_error: 117  Retry # : 1
[1970-Jan-15 19:37:06.352429]: Toolhead 0 : Retry: Waited 0.613446s from state change
[1970-Jan-15 19:38:12.431665]: Steps overrun! last 65533 and just got 0
[1970-Jan-15 19:38:12.433413]: calculated 2
[1970-Jan-15 19:40:07.464076]: Toolhead 0 : Retry: Waited 0.609208s from state change
[1970-Jan-15 19:41:11.606479]: Expected packet id: 0xc4, Got packet id: 0x89, Full packet: 
0x12,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0xf3,0x0,0x0,0x2d,0x0,0xd5,0x0,0xf,0x31,0x89,0x1,0x0,0xd7,0x0,

[1970-Jan-15 19:41:11.621098]: Toolhead 0 : Toolhead Response Fail with comm_error: 117  Retry # : 1
[1970-Jan-15 19:42:07.235200]: Toolhead 0 : Retry: Waited 0.652537s from state change
[1970-Jan-15 19:46:19.484397]: Expected packet id: 0x8a, Got packet id: 0x1, Full packet: 
0x12,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0xf3,0xf,0x0,0x2d,0x0,0xd6,0x0,0xf,0x89,0x9c,0x1,0x0,0xd7,0x0,0x1,0x44,0x41,0x3,0x52,

[1970-Jan-15 19:46:19.486482]: Toolhead 0 : Toolhead Response Fail with comm_error: 117  Retry # : 1
[1970-Jan-15 19:46:50.039153]: Expected packet id: 0x1b, Got packet id: 0x1a, Full packet: 
0xf3,0x0,0x0,0x2d,0x0,0xda,0x0,0xf,0x92,0x53,0x1,0x0,0xd7,0x0,0x1,0x44,0x41,0x3,0x52,0x1,0x1,0x0,0x0,0x0,0x0,0xc4,0x0,0x1a,0x91,0xcb,0xdb,0x8c,

[1970-Jan-15 19:46:50.051771]: Toolhead 0 : Toolhead Response Fail with comm_error: 117  Retry # : 1
[1970-Jan-15 19:47:47.321868]: Expected packet id: 0x7f, Got packet id: 0x7e, Full packet: 
0xf3,0x0,0x0,0x2d,0x0,0xd5,0x0,0xf,0xa3,0x2f,0x1,0x0,0xd7,0x0,0x1,0x44,0x41,0x3,0x52,0x1,0x1,0x0,0x0,0x0,0x0,0xda,0x0,0x7e,0xbc,0xf6,0x5a,0x6,

[1970-Jan-15 19:47:47.323825]: Toolhead 0 : Toolhead Response Fail with comm_error: 117  Retry # : 1
[1970-Jan-15 19:48:38.888757]: TH0: 322 failures in last 65536 packets (0.491333%)
[1970-Jan-15 19:49:56.283513]: Expected packet id: 0x7b, Got packet id: 0x7a, Full packet: 
0xf3,0x0,0x0,0x2d,0x0,0xd8,0x0,0xf,0xc8,0x6b,0x1,0x0,0xd7,0x0,0x1,0x44,0x41,0x3,0x52,0x1,0x1,0x0,0x0,0x0,0x0,0xdc,0x0,0x7a,0x9d,0x96,0x60,0x63,

[1970-Jan-15 19:49:56.285621]: Toolhead 0 : Toolhead Response Fail with comm_error: 117  Retry # : 1
[1970-Jan-15 19:50:04.124217]: Expected packet id: 0xc0, Got packet id: 0xbf, Full packet: 
0xf3,0x0,0x0,0x2d,0x0,0xda,0x0,0xf,0xca,0x85,0x1,0x0,0xd7,0x0,0x1,0x44,0x41,0x3,0x52,0x1,0x1,0x0,0x0,0x0,0x0,0x9,0x0,0xbf,0xbf,0x62,0x50,0x18,

[1970-Jan-15 19:50:04.130257]: Toolhead 0 : Toolhead Response Fail with comm_error: 117  Retry # : 1
[1970-Jan-15 19:50:21.945415]: Expected packet id: 0x89, Got packet id: 0x1, Full packet: 
0x12,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0xf3,0x0,0x0,0x2d,0x0,0xd9,0x0,0xf,0xcf,0xf5,0x1,0x0,0xd7,0x0,0x1,0x44,0x41,0x3,0x52,

[1970-Jan-15 19:50:21.947405]: Toolhead 0 : Toolhead Response Fail with comm_error: 117  Retry # : 1
[1970-Jan-15 19:50:53.043566]: Expected packet id: 0x40, Got packet id: 0x0, Full packet: 
0x12,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0xf3,0xf,0x0,0x2d,0x0,0xd5,0x0,0xf,0xd9,0x9c,0x1,0x0,0xd7,0x0,0x1,0x44,0x41,0x3,

[1970-Jan-15 19:50:53.045646]: Toolhead 0 : Toolhead Response Fail with comm_error: 117  Retry # : 1
[1970-Jan-15 19:52:42.934587]: Expected packet id: 0x5c, Got packet id: 0x5b, Full packet: 
0xf3,0x0,0x0,0x2d,0x0,0xd9,0x0,0xf,0xfa,0xc,0x1,0x0,0xd7,0x0,0x1,0x44,0x41,0x3,0x52,0x1,0x1,0x0,0x0,0x0,0x2,0x15,0x0,0x5b,0x6f,0xbd,0x63,0x78,

[1970-Jan-15 19:52:42.936558]: Toolhead 0 : Toolhead Response Fail with comm_error: 117  Retry # : 1
[1970-Jan-15 19:53:05.357853]: Steps overrun! last 65534 and just got 1
[1970-Jan-15 19:53:05.359909]: calculated 2
[1970-Jan-15 19:54:38.935394]: Expected packet id: 0x84, Got packet id: 0x83, Full packet: 
0xf3,0x0,0x0,0x2d,0x0,0xd5,0x0,0xf,0x19,0x48,0x1,0x0,0xd7,0x0,0x1,0x44,0x41,0x3,0x52,0x1,0x1,0x0,0x0,0x0,0x1,0x1c,0x0,0x83,0xb5,0x8,0x53,0x7b,

[1970-Jan-15 19:54:38.937470]: Toolhead 0 : Toolhead Response Fail with comm_error: 117  Retry # : 1
[1970-Jan-15 19:56:08.285033]: Toolhead 0 : Retry: Waited 0.715376s from state change
[1970-Jan-15 19:58:09.962022]: Expend Buffer: true
[1970-Jan-15 19:58:10.261093]: Toolhead 0 commands idle
[1970-Jan-15 19:58:19.592781]: libstepper: false toolhead: false( ignored: false) acceleration_manager: true
[1970-Jan-15 19:58:25.336428]: Buffer stall ongoing: 9804
[1970-Jan-15 19:58:25.440911]: Buffer stall ongoing: 31863
[1970-Jan-15 19:58:25.552870]: Buffer stall ongoing: 55857
[1970-Jan-15 19:58:25.586960]: Last sync period had (0,139314,255459) buffer fulls due to suspend moves
[1970-Jan-15 19:58:25.588822]: Syncing turned false
[1970-Jan-15 19:58:25.665233]: PRU Event: PRU_SYNC_OFF(0)
[1970-Jan-15 19:58:25.667862]: Buffer stall ongoing: 63468
[1970-Jan-15 19:58:27.372269]: Toolhead 0  ADC Error: 0
[1970-Jan-15 19:58:30.398055]: libstepper: false toolhead: true( ignored: false) acceleration_manager: true
[1970-Jan-15 19:58:37.951422]: libstepper: false toolhead: true( ignored: false) acceleration_manager: true
[1970-Jan-15 19:58:39.228408]: Last sync period had (0,139314,256020) buffer fulls due to suspend moves
[1970-Jan-15 19:58:39.240545]: Syncing turned false
[1970-Jan-15 19:58:39.242386]: TH0: 127 failures in last 29466 packets (0.431005%)
[1970-Jan-15 19:58:39.244382]: Toolhead Abort
[1970-Jan-15 19:58:39.246230]: aborting pru with shutdown=true
[1970-Jan-15 19:58:39.257110]: Last sync period had (0,139314,256020) buffer fulls due to suspend moves
[1970-Jan-15 19:58:39.258938]: Libstepper All Axis Abort
[1970-Jan-15 19:58:39.271792]: Heater manager Set Target Temperature to 0, index 0
[1970-Jan-15 19:58:39.273596]: Sent heater settings hold timeout 3min, rise timeout 1min, rise threshold 10C, sag threhsold 20C, overrun threshold 20C, fan preload 15C, preload tick delay 8900ticks, temperature freeze timeout 54464ms (may be discretized)
[1970-Jan-15 19:58:39.478422]: Heater manager Set Target Temperature to 0, index 0
[1970-Jan-15 19:58:39.497889]: Sent heater settings hold timeout 3min, rise timeout 1min, rise threshold 10C, sag threhsold 20C, overrun threshold 20C, fan preload 15C, preload tick delay 8900ticks, temperature freeze timeout 54464ms (may be discretized)
[1970-Jan-15 19:58:39.606999]: Commanding stats update: Retract count: 1628733900
[1970-Jan-15 19:58:39.620880]: Toolhead 0 marked as possibly blocking!
[1970-Jan-15 19:58:40.291427]: Toolhead 0 done blocking!
[1970-Jan-15 19:58:40.463414]: GetToolUsageStats called in machine  state 0
[1970-Jan-15 19:58:40.465214]: Commanding tool usage stat retrieve
[1970-Jan-15 19:58:40.466932]: GetToolUsageState: Proceeds to 1
[1970-Jan-15 19:58:40.468599]: GetToolUsagState: Error from retrieve: 0x10a
[1970-Jan-15 19:58:40.523222]: Raw usage stats: retract 3257466804ct, extrusion 236237071 steps, 1011654 seconds, refurbed 0 times
[1970-Jan-15 19:58:40.607508]: GetToolUsageStats called in machine  state 1
[1970-Jan-15 19:58:40.609282]: VerifyToolUsageStatsRetrieved: Done
[1970-Jan-15 19:58:40.621356]: GetToolUsageState: Proceeds to 2
[1970-Jan-15 19:58:40.698338]: GetToolUsageStats called in machine  state 2
[1970-Jan-15 19:58:40.710585]: GetToolUsageState: Done, resets
[1970-Jan-15 20:06:09.945239]: Heater manager Set Target Temperature to 180, index 0
[1970-Jan-15 20:06:09.947389]: Sent heater settings hold timeout 3min, rise timeout 1min, rise threshold 10C, sag threhsold 20C, overrun threshold 20C, fan preload 15C, preload tick delay 8900ticks, temperature freeze timeout 54464ms (may be discretized)
[1970-Jan-15 20:06:11.209663]: HOME: axis 1, speed 22, flip dir false, sp true, blocking false
[1970-Jan-15 20:06:11.212097]: Load Sense Limit Method: 1
[1970-Jan-15 20:06:11.227575]: Last sync period had (0,139314,277209) buffer fulls due to suspend moves
[1970-Jan-15 20:06:11.229440]: Libstepper All Axis Abort
[1970-Jan-15 20:06:17.106170]: libstepper: false toolhead: true( ignored: false) acceleration_manager: true
[1970-Jan-15 20:06:17.980665]: HOME: 1 homing: Limit Detected!: 
[1970-Jan-15 20:06:17.982551]: Toolhead Abort
[1970-Jan-15 20:06:17.984351]: aborting pru with shutdown=true
[1970-Jan-15 20:06:17.987259]: Last sync period had (0,139314,277509) buffer fulls due to suspend moves
[1970-Jan-15 20:06:17.989952]: Libstepper All Axis Abort
[1970-Jan-15 20:06:18.069725]: HOME: 1 homing: Limit Detected!: 
[1970-Jan-15 20:06:20.105848]: HOME: axis 0, speed 22, flip dir false, sp true, blocking false
[1970-Jan-15 20:06:20.108123]: Load Sense Limit Method: 0
[1970-Jan-15 20:06:20.116789]: Last sync period had (0,139314,277605) buffer fulls due to suspend moves
[1970-Jan-15 20:06:20.118656]: Libstepper All Axis Abort
[1970-Jan-15 20:06:24.742777]: libstepper: false toolhead: true( ignored: false) acceleration_manager: true
[1970-Jan-15 20:06:31.078771]: libstepper: false toolhead: true( ignored: false) acceleration_manager: true
[1970-Jan-15 20:06:34.267330]: HOME: 0 homing: Limit Detected!: 
[1970-Jan-15 20:06:34.269225]: Toolhead Abort
[1970-Jan-15 20:06:34.291512]: aborting pru with shutdown=true
[1970-Jan-15 20:06:34.294322]: Last sync period had (0,139314,278313) buffer fulls due to suspend moves
[1970-Jan-15 20:06:34.296282]: Libstepper All Axis Abort
[1970-Jan-15 20:06:34.374261]: HOME: 0 homing: Limit Detected!: 
[1970-Jan-15 20:06:37.137754]: HOME: axis 2, speed 8, flip dir false, sp true, blocking false
[1970-Jan-15 20:06:38.384212]: libstepper: false toolhead: true( ignored: false) acceleration_manager: true
[1970-Jan-15 20:06:44.185086]: libstepper: false toolhead: true( ignored: false) acceleration_manager: true
[1970-Jan-15 20:06:49.852638]: libstepper: false toolhead: true( ignored: false) acceleration_manager: true
[1970-Jan-15 20:06:54.311933]: Last sync period had (0,139314,279447) buffer fulls due to suspend moves
[1970-Jan-15 20:06:54.314883]: Syncing turned false
[1970-Jan-15 20:06:54.316841]: Toolhead Abort
[1970-Jan-15 20:06:54.318637]: aborting pru with shutdown=true
[1970-Jan-15 20:06:54.331944]: Last sync period had (0,139314,279447) buffer fulls due to suspend moves
[1970-Jan-15 20:06:54.333800]: Libstepper All Axis Abort
[1970-Jan-15 20:06:54.335497]: Heater manager Set Target Temperature to 0, index 0
[1970-Jan-15 20:06:54.337413]: Sent heater settings hold timeout 3min, rise timeout 1min, rise threshold 10C, sag threhsold 20C, overrun threshold 20C, fan preload 15C, preload tick delay 8900ticks, temperature freeze timeout 54464ms (may be discretized)
[1970-Jan-15 20:06:57.474652]: libstepper: false toolhead: true( ignored: false) acceleration_manager: true
[1970-Jan-15 20:07:04.708660]: libstepper: false toolhead: true( ignored: false) acceleration_manager: true
[1970-Jan-15 20:07:05.937659]: Last sync period had (0,139314,279918) buffer fulls due to suspend moves
[1970-Jan-15 20:07:05.939523]: Syncing turned false
[1970-Jan-15 20:07:05.951703]: Toolhead Abort
[1970-Jan-15 20:07:05.954281]: aborting pru with shutdown=true
[1970-Jan-15 20:07:05.957089]: Last sync period had (0,139314,279918) buffer fulls due to suspend moves
[1970-Jan-15 20:07:05.958930]: Libstepper All Axis Abort
[1970-Jan-15 20:07:05.962477]: Heater manager Set Target Temperature to 0, index 0
[1970-Jan-15 20:07:05.964271]: Sent heater settings hold timeout 3min, rise timeout 1min, rise threshold 10C, sag threhsold 20C, overrun threshold 20C, fan preload 15C, preload tick delay 8900ticks, temperature freeze timeout 54464ms (may be discretized)
[1970-Jan-15 20:07:06.112858]: Heater manager Set Target Temperature to 0, index 0
[1970-Jan-15 20:07:06.114693]: Sent heater settings hold timeout 3min, rise timeout 1min, rise threshold 10C, sag threhsold 20C, overrun threshold 20C, fan preload 15C, preload tick delay 8900ticks, temperature freeze timeout 54464ms (may be discretized)
[1970-Jan-15 20:07:06.247798]: Commanding stats update: Retract count: 3257466804
[1970-Jan-15 20:07:06.249562]: Toolhead 0 marked as possibly blocking!
[1970-Jan-15 20:07:06.901248]: Toolhead 0 done blocking!
[1970-Jan-15 20:07:07.117283]: GetToolUsageStats called in machine  state 0
[1970-Jan-15 20:07:07.119221]: Commanding tool usage stat retrieve
[1970-Jan-15 20:07:07.138033]: GetToolUsageState: Proceeds to 1
[1970-Jan-15 20:07:07.139713]: GetToolUsagState: Error from retrieve: 0x10a
[1970-Jan-15 20:07:07.265221]: Raw usage stats: retract 2219966312ct, extrusion 236237071 steps, 1011654 seconds, refurbed 0 times
[1970-Jan-15 20:07:07.307894]: GetToolUsageStats called in machine  state 1
[1970-Jan-15 20:07:07.309685]: VerifyToolUsageStatsRetrieved: Done
[1970-Jan-15 20:07:07.317800]: GetToolUsageState: Proceeds to 2
[1970-Jan-15 20:07:07.411001]: GetToolUsageStats called in machine  state 2
[1970-Jan-15 20:07:07.412802]: GetToolUsageState: Done, resets
[1970-Jan-15 20:07:29.233137]: Heater manager Set Target Temperature to 180, index 0
[1970-Jan-15 20:07:29.234930]: Sent heater settings hold timeout 3min, rise timeout 1min, rise threshold 10C, sag threhsold 20C, overrun threshold 20C, fan preload 15C, preload tick delay 8900ticks, temperature freeze timeout 54464ms (may be discretized)
[1970-Jan-15 20:07:30.614840]: HOME: axis 1, speed 22, flip dir false, sp true, blocking false
[1970-Jan-15 20:07:30.616880]: Load Sense Limit Method: 1
[1970-Jan-15 20:07:30.630849]: Last sync period had (0,139314,280146) buffer fulls due to suspend moves
[1970-Jan-15 20:07:30.632818]: Libstepper All Axis Abort
[1970-Jan-15 20:07:36.235617]: libstepper: false toolhead: true( ignored: false) acceleration_manager: true
[1970-Jan-15 20:07:37.253880]: HOME: 1 homing: Limit Detected!: 
[1970-Jan-15 20:07:37.255899]: Toolhead Abort
[1970-Jan-15 20:07:37.257689]: aborting pru with shutdown=true
[1970-Jan-15 20:07:37.262092]: Last sync period had (0,139314,280440) buffer fulls due to suspend moves
[1970-Jan-15 20:07:37.263961]: Libstepper All Axis Abort
[1970-Jan-15 20:07:37.329633]: HOME: 1 homing: Limit Detected!: 
[1970-Jan-15 20:07:39.230431]: HOME: axis 0, speed 22, flip dir false, sp true, blocking false
[1970-Jan-15 20:07:39.241656]: Load Sense Limit Method: 0
[1970-Jan-15 20:07:39.244642]: CLEAR BUFFER FAIL! in libstepper::Abort()
[1970-Jan-15 20:07:39.250845]: Last sync period had (0,139314,280530) buffer fulls due to suspend moves
[1970-Jan-15 20:07:39.252680]: Libstepper All Axis Abort
[1970-Jan-15 20:07:44.109090]: libstepper: false toolhead: true( ignored: false) acceleration_manager: true
[1970-Jan-15 20:07:51.477756]: libstepper: false toolhead: true( ignored: false) acceleration_manager: true
[1970-Jan-15 20:07:53.320317]: HOME: 0 homing: Limit Detected!: 
[1970-Jan-15 20:07:53.322257]: Toolhead Abort
[1970-Jan-15 20:07:53.324041]: aborting pru with shutdown=true
[1970-Jan-15 20:07:53.326891]: Last sync period had (0,139314,281175) buffer fulls due to suspend moves
[1970-Jan-15 20:07:53.328727]: Libstepper All Axis Abort
[1970-Jan-15 20:07:53.423966]: HOME: 0 homing: Limit Detected!: 
[1970-Jan-15 20:07:56.224619]: HOME: axis 2, speed 8, flip dir false, sp true, blocking false
[1970-Jan-15 20:07:59.023479]: libstepper: false toolhead: true( ignored: false) acceleration_manager: true
[1970-Jan-15 20:08:05.334553]: libstepper: false toolhead: true( ignored: false) acceleration_manager: true
[1970-Jan-15 20:08:12.658642]: libstepper: false toolhead: true( ignored: false) acceleration_manager: true
[1970-Jan-15 20:08:17.776648]: HOME: 2 homing: Limit Detected!: 
[1970-Jan-15 20:08:17.778495]: Toolhead Abort
[1970-Jan-15 20:08:17.780489]: aborting pru with shutdown=false
[1970-Jan-15 20:08:17.785538]: Last sync period had (0,139314,282399) buffer fulls due to suspend moves
[1970-Jan-15 20:08:17.788254]: Libstepper All Axis Abort
[1970-Jan-15 20:08:17.872958]: HOME: 2 homing: Limit Detected!: 
[1970-Jan-15 20:08:18.672545]: HOME: axis 2, speed 0.5, flip dir false, sp true, blocking true
[1970-Jan-15 20:08:18.957173]: libstepper: false toolhead: false( ignored: false) acceleration_manager: true
[1970-Jan-15 20:08:19.288163]: libstepper: false toolhead: false( ignored: false) acceleration_manager: true
[1970-Jan-15 20:08:19.625484]: libstepper: false toolhead: false( ignored: false) acceleration_manager: true
[1970-Jan-15 20:08:19.950558]: libstepper: false toolhead: false( ignored: false) acceleration_manager: true
[1970-Jan-15 20:08:20.316024]: libstepper: false toolhead: false( ignored: false) acceleration_manager: true
[1970-Jan-15 20:08:20.664925]: libstepper: false toolhead: false( ignored: false) acceleration_manager: true
[1970-Jan-15 20:08:21.016248]: libstepper: false toolhead: false( ignored: false) acceleration_manager: true
[1970-Jan-15 20:08:21.342484]: libstepper: false toolhead: false( ignored: false) acceleration_manager: true
[1970-Jan-15 20:08:21.727204]: libstepper: false toolhead: false( ignored: false) acceleration_manager: true
[1970-Jan-15 20:08:22.067636]: libstepper: false toolhead: false( ignored: false) acceleration_manager: true
[1970-Jan-15 20:08:22.393918]:  wait for axis 0 full: false offset: 108 l3map offset:    126 status: 1 position -4235 status count 1001
[1970-Jan-15 20:08:22.412468]: libstepper: false toolhead: false( ignored: false) acceleration_manager: true
[1970-Jan-15 20:08:22.621627]: HOME: 2 homing: Limit Detected!: 
[1970-Jan-15 20:08:22.623472]: Toolhead Abort
[1970-Jan-15 20:08:22.625911]: aborting pru with shutdown=false
[1970-Jan-15 20:08:22.638677]: Last sync period had (0,139314,282453) buffer fulls due to suspend moves
[1970-Jan-15 20:08:22.640768]: Libstepper All Axis Abort
[1970-Jan-15 20:08:22.706873]: HOME: 2 homing: Limit Detected!: 
[1970-Jan-15 20:08:22.920817]: GAP: Query->Await
[1970-Jan-15 20:08:22.972495]: TH0: Retreived step position 9699599
[1970-Jan-15 20:08:23.004004]: wait for PRU status in get position
[1970-Jan-15 20:08:23.019711]: wait for PRU status in get position
[1970-Jan-15 20:08:23.021605]: GAP: Await->Done(Query)
[1970-Jan-15 20:08:23.355219]: Heater manager Set Target Temperature to 180, index 0
[1970-Jan-15 20:08:23.357138]: Sent heater settings hold timeout 3min, rise timeout 1min, rise threshold 10C, sag threhsold 20C, overrun threshold 20C, fan preload 15C, preload tick delay 8900ticks, temperature freeze timeout 54464ms (may be discretized)
[1970-Jan-15 20:08:24.230295]: Expecting 138311 steps extruded this print from 1274.17 mm of plastic
[1970-Jan-15 20:08:24.465896]: Heater manager Set Target Temperature to 215, index 0
[1970-Jan-15 20:08:24.471541]: Sent heater settings hold timeout 3min, rise timeout 1min, rise threshold 10C, sag threhsold 20C, overrun threshold 20C, fan preload 15C, preload tick delay 8900ticks, temperature freeze timeout 54464ms (may be discretized)
[1970-Jan-15 20:08:24.657367]: wait for heaters at target, wait bitmask 0x1
[1970-Jan-15 20:08:34.257660]: libstepper: false toolhead: true( ignored: false) acceleration_manager: true
[1970-Jan-15 20:08:41.864488]: libstepper: false toolhead: true( ignored: false) acceleration_manager: true
[1970-Jan-15 20:08:47.147281]: Last sync period had (0,139314,283515) buffer fulls due to suspend moves
[1970-Jan-15 20:08:47.149813]: Syncing turned false
[1970-Jan-15 20:08:47.168723]: Toolhead Abort
[1970-Jan-15 20:08:47.173525]: aborting pru with shutdown=true
[1970-Jan-15 20:08:47.192107]: Last sync period had (0,139314,283515) buffer fulls due to suspend moves
[1970-Jan-15 20:08:47.193975]: Libstepper All Axis Abort
[1970-Jan-15 20:08:47.195820]: Heater manager Set Target Temperature to 0, index 0
[1970-Jan-15 20:08:47.197662]: Sent heater settings hold timeout 3min, rise timeout 1min, rise threshold 10C, sag threhsold 20C, overrun threshold 20C, fan preload 15C, preload tick delay 8900ticks, temperature freeze timeout 54464ms (may be discretized)
[1970-Jan-15 20:08:47.398137]: Heater manager Set Target Temperature to 0, index 0
[1970-Jan-15 20:08:47.399959]: Sent heater settings hold timeout 3min, rise timeout 1min, rise threshold 10C, sag threhsold 20C, overrun threshold 20C, fan preload 15C, preload tick delay 8900ticks, temperature freeze timeout 54464ms (may be discretized)
[1970-Jan-15 20:08:47.522728]: Commanding stats update: Retract count: 2219966312
[1970-Jan-15 20:08:47.531690]: Toolhead 0 marked as possibly blocking!
[1970-Jan-15 20:08:48.179185]: Toolhead 0 done blocking!
[1970-Jan-15 20:08:48.345852]: GetToolUsageStats called in machine  state 0
[1970-Jan-15 20:08:48.347792]: Commanding tool usage stat retrieve
[1970-Jan-15 20:08:48.349580]: GetToolUsageState: Proceeds to 1
[1970-Jan-15 20:08:48.351536]: GetToolUsagState: Error from retrieve: 0x10a
[1970-Jan-15 20:08:48.387148]: Raw usage stats: retract 144965328ct, extrusion 236237071 steps, 1011654 seconds, refurbed 0 times
[1970-Jan-15 20:08:48.426849]: GetToolUsageStats called in machine  state 1
[1970-Jan-15 20:08:48.429548]: VerifyToolUsageStatsRetrieved: Done
[1970-Jan-15 20:08:48.431490]: GetToolUsageState: Proceeds to 2
[1970-Jan-15 20:08:48.488376]: GetToolUsageStats called in machine  state 2
[1970-Jan-15 20:08:48.490509]: GetToolUsageState: Done, resets
[1970-Jan-15 20:39:42.232234]: Heater manager Set Target Temperature to 180, index 0
[1970-Jan-15 20:39:42.234039]: Sent heater settings hold timeout 3min, rise timeout 1min, rise threshold 10C, sag threhsold 20C, overrun threshold 20C, fan preload 15C, preload tick delay 8900ticks, temperature freeze timeout 54464ms (may be discretized)
[1970-Jan-15 20:39:43.714199]: bronx lowest mem space: 0x34e bytes
[1970-Jan-15 20:39:47.723515]: Heater manager Set Target Temperature to 215, index 0
[1970-Jan-15 20:39:47.725328]: Sent heater settings hold timeout 3min, rise timeout 1min, rise threshold 10C, sag threhsold 20C, overrun threshold 20C, fan preload 15C, preload tick delay 8900ticks, temperature freeze timeout 54464ms (may be discretized)
[1970-Jan-15 20:39:48.957795]: wait for heaters at target, wait bitmask 0x1
[1970-Jan-15 20:42:59.166811]: libstepper: false toolhead: true( ignored: false) acceleration_manager: true
[1970-Jan-15 20:43:04.737782]: Raw HES proceeding
[1970-Jan-15 20:43:04.754426]: Got raw val 23072, saturated: true
[1970-Jan-15 20:43:04.780477]: Returning HES
[1970-Jan-15 20:43:04.782338]: Sending back val 23072, saturated true
[1970-Jan-15 20:43:04.849453]: Toolhead Abort
[1970-Jan-15 20:43:04.851534]: aborting pru with shutdown=true
[1970-Jan-15 20:43:04.854442]: Last sync period had (0,139314,304659) buffer fulls due to suspend moves
[1970-Jan-15 20:43:04.856268]: Libstepper All Axis Abort
[1970-Jan-15 20:43:30.051883]: Toolhead 0 state error: 80
[1970-Jan-15 20:43:36.610930]: Toolhead 0 state error: 54
[1970-Jan-15 20:43:36.612706]: Tool UID becomes 0.